Коды ошибок Toshiba
Предлагаем ознакомиться с кодами ошибок Toshiba. В данном разделе приведены ошибки популярных моделей копировальных аппаратов Toshiba и причины их возникновения. В случае появления серьезной неисправности, мы не рекомендует проводить ремонт аппарата самостоятельно, а советуем обратиться в сервисный центр.
Toshiba 1710
| Код ошибки | Описание |
|---|---|
| A1 | Charge corona cleaner problem |
| A2 | ADD problem |
| A4 | Sorter problem |
| A5 | Board problem |
| A6 | Sorter board problem |
| A7 | ADF interface |
| A0 | Communication problem between main board and PFC |
| C1 | Board problem |
| C2 | Board problem |
| C3 | Board problem |
| C4 | Board problem |
| C5 | Optics locked or not initialized. Could be scan or lens/mirror |
| C7 | Fuser thermistoe problem, or low temperature |
| C8 | Scan motor won't shut off |
| CA | Main board problem |
| CB | ADF drive problem |
| CC | ADF drive problem |
| CD | BC RAM hardware |
| CE | BC RAM software |
| CP | Drive problem |
| E0 | Waste toner full |
| E1 | Jam |
| E2 | Fuser jam |
| E3 | Jam |
| E4 | Front door was opened during copy run |
| E5 | Feed jam |
| E8 | Jam in ADD (duplex) |
| E9 | Jam in pedestal |
| EC | ADF jam |
| ED | ADF jam |
| EE | ADF exit/reverse jam |
Toshiba 2050
| Код ошибки | Описание |
|---|---|
| A4 | Sorter problem |
| A5 | Communication problem between main CPU and IPC |
| A6 | Sorter interface problem |
| C2 | Communication problem between CPU's |
| C5 | Scan or optic problem. Locked up or won't initialize or return to home position |
| C7 | Fuser problem. After repairing problem, go to "0 & 8 mode", code 87 to reset |
| CF | Developer calibration problem |
| CP | Drive problem |
| E1 | Paper jam |
| E2 | Fuser jam |
| E3 | Paper jam |
| E4 | Front door opened during copy cycle |
| E5 | Paper feed jam |
Toshiba 2060
| Код ошибки | Описание |
|---|---|
| C01 | Main motor drive problem |
| C04 | Pedestal main drive problem |
| C05 | Duplex drive problem |
| C11 | Duplex exit motor |
| C12 | Duplex end motor |
| C13 | Upper cassette |
| C14 | Lower cassette |
| C15 | Pedestal upper cassette |
| C16 | Pedestal middle cassette |
| C17 | Pedestal lower cassette |
| C18 | LCT |
| C21 | Scan problem |
| C22 | Lens problem |
| C23 | Mirror motor |
| C26 | Exposure lamp |
| C27 | Scan motor |
| C33 | Set up failure |
| C35 | Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona |
| C41 | Fuser thermistor or low temperature |
| C43 | Fuser problem after warm-up |
| C44 | Fuser problem after warm-up |
| C45 | Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time |
| E01 | Jam |
| E02 | Fuser jam |
| E03 | Jam at turn on |
| E04 | Front door opened during copy cycle |
| E05 | Registration jam |
| E08 | Duplex unit jam |
| E11 | Duplex jam |
| E12 | Bypass jam |
| E13 | Upper cassette jam |
| E14 | 2nd cassette jam |
| E15 | 3rd cassette jam |
| E16 | 4th cassette jam |
| E17 | 4th cassette jam |
| E19 | CT jam |
| E21 | LCT jam |
| E22-E25 | Paper jams in copier |
| E71 | ADF feed jam |
| E72 | ADF transport jam |
| E73 | ADF exit jam |
| E74 | RADF jam |
| E75 | ADF 2nd original jam |
| E81-E85 | Sorter jam |
| E88 | Jam after sorter |